{"id":312710,"date":"2024-10-19T21:30:43","date_gmt":"2024-10-19T21:30:43","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/bs-en-iso-1452-22009\/"},"modified":"2024-10-25T19:32:14","modified_gmt":"2024-10-25T19:32:14","slug":"bs-en-iso-1452-22009","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/bsi\/bs-en-iso-1452-22009\/","title":{"rendered":"BS EN ISO 1452-2:2009"},"content":{"rendered":"

This part of ISO 1452 specifies the characteristics of solid-wall pipes made from unplasticized poly(vinyl chloride) (PVC-U) for piping systems intended for water supply and for buried and above-ground drainage and sewerage under pressure.<\/p>\n

It also specifies the test parameters for the test methods referred to in this part of ISO 1452.<\/p>\n

In conjunction with ISO 1452-1 and ISO 1452-5, it is applicable to extruded PVC-U pipes without a socket and pipes with a socket (integral or not), intended to be used for the following:<\/p>\n

    \n
  1. \n

    water mains and services buried in the ground;<\/p>\n<\/li>\n

  2. \n

    conveyance of water above ground for both outside and inside buildings;<\/p>\n<\/li>\n

  3. \n

    buried and above-ground drainage and sewerage under pressure.<\/p>\n<\/li>\n<\/ol>\n

    It is applicable to piping systems intended for the supply of water under pressure up to and including 25 \u00b0C (cold water) intended for human consumption and for general purposes as well as for waste water under pressure.<\/p>\n

    This part of ISO 1452 specifies pipes for the conveyance of water and waste water up to and including 45 \u00b0C. For temperatures between 25 \u00b0C and 45 \u00b0C, Figure A.1 applies.<\/p>\n

    \n

    NOTE 1 The producer and the end-user can come to agreement on the possibilities of use for temperatures above 45 \u00b0C on a case-by-case basis.<\/p>\n<\/blockquote>\n

    This part of ISO 1452 specifies a range of pipe sizes and pressure classes, and gives requirements concerning colours.<\/p>\n

    \n

    NOTE 2 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.<\/p>\n<\/blockquote>\n

    PDF Catalog<\/h4>\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n\n
    PDF Pages<\/th>\nPDF Title<\/th>\n<\/tr>\n
    9<\/td>\nScope
    Normative references <\/td>\n<\/tr>\n
    10<\/td>\nTerms, definitions, symbols and abbreviated terms <\/td>\n<\/tr>\n
    11<\/td>\nMaterial
    Pipe material
    Density
    MRS\u02davalue
    General characteristics
    Appearance
    Colour
    Opacity of pipes intended for the above-ground conveyance of
    Geometrical characteristics
    Measurement of dimensions
    Nominal outside diameters <\/td>\n<\/tr>\n
    12<\/td>\nMean outside diameters and their tolerances <\/td>\n<\/tr>\n
    13<\/td>\nWall thickness and their tolerances <\/td>\n<\/tr>\n
    14<\/td>\nLength of pipe <\/td>\n<\/tr>\n
    15<\/td>\nPipes with sockets
    Sockets for solvent cementing <\/td>\n<\/tr>\n
    16<\/td>\nSockets for elastomeric ring seal type joints <\/td>\n<\/tr>\n
    19<\/td>\nPipe ends for ring seal or solvent cement joints
    Classification and selection of pipes
    Classification
    Selection of nominal pressure and pipe series S for water up
    Determination of the allowable operating pressure for water
    Mechanical characteristics
    Impact strength <\/td>\n<\/tr>\n
    20<\/td>\nResistance to internal pressure <\/td>\n<\/tr>\n
    21<\/td>\nPhysical characteristics <\/td>\n<\/tr>\n
    22<\/td>\nSealing rings
    Adhesives
    Performance requirements
    Marking
    General
    Minimum required marking <\/td>\n<\/tr>\n
    23<\/td>\nAdditional marking <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":"

    Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure. Unplasticized poly(vinyl chloride) (PVC U) – Pipes<\/b><\/p>\n\n\n\n\n
    Published By<\/td>\nPublication Date<\/td>\nNumber of Pages<\/td>\n<\/tr>\n
    BSI<\/b><\/a><\/td>\n2010<\/td>\n32<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n","protected":false},"featured_media":312715,"template":"","meta":{"rank_math_lock_modified_date":false,"ep_exclude_from_search":false},"product_cat":[351,2641],"product_tag":[],"class_list":{"0":"post-312710","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-23-040-45","7":"product_cat-bsi","9":"first","10":"instock","11":"sold-individually","12":"shipping-taxable","13":"purchasable","14":"product-type-simple"},"_links":{"self":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product\/312710","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/types\/product"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media\/312715"}],"wp:attachment":[{"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/media?parent=312710"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_cat?post=312710"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/pdfstandards.shop\/wp-json\/wp\/v2\/product_tag?post=312710"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}