BS EN 754-8:2016
$102.76
Aluminium and aluminium alloys. Cold drawn rod/bar and tube – Porthole tubes, tolerances on dimensions and form
| Published By | Publication Date | Number of Pages |
| BSI | 2016 | 22 |
This European Standard specifies the tolerances on dimensions and form for aluminium and aluminium alloy cold drawn porthole tubes with an outside diameter ( OD) from 3 mm to 350 mm (round tube, see Figure 1) or with a cross section contained within a circumscribing circle ( CD) from 8 mm to 300 mm (other than round tube, see Figure 2), supplied in straight lengths.
This document only applies to cold drawn tube for general engineering applications made in the following alloys:
-
EN AW‑1050A , EN AW‑1200 ;
-
EN AW‑3003 , EN AW‑3103 ;
-
EN AW‑5005 , EN AW‑5005A , EN AW‑5049 , EN AW‑5251 , EN AW‑5052 ;
-
EN AW‑6012 , EN AW‑6060 , EN AW‑6061 , EN AW‑6262 , EN AW‑6262A ;
-
EN AW‑6063 , EN AW‑6063A , EN AW‑6065 , EN AW‑6082 ;
-
EN AW‑7020 .
The temper designations used in this part are according to EN 515 .
This document only applies to tube produced by the porthole/bridge method of extrusion only (and then cold drawn to the final dimensions).
This document does not apply to:
-
cold drawn tubes produced by the seamless, die/mandrel method ( EN 754‑7 ),
-
tubes delivered in coils ( EN 13958 ),
-
coiled tubes cut to length ( EN 13958 ).
[Image removed.]
[Image removed.]
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 4 | Contents Page |
| 5 | European foreword |
| 6 | 1 Scope Figure 1 — Round tube |
| 7 | Figure 2 — Circumscribing circle for other than round tube 2 Normative references 3 Tolerances on dimensions 3.1 General 3.2 Diameter – Round tube |
| 8 | Table 1 — Tolerances on diameter for round tube 3.3 Width, depth or width across flats – squares, rectangles, hexagons, octagons |
| 9 | Table 2 — Tolerances on width, depth or width across flats 3.4 Wall thickness variation (eccentricity) |
| 10 | Table 3 — Tolerances on wall thickness variation (eccentricity) for round tubes 3.5 Length Table 4 — Tolerances on fixed length |
| 11 | 3.6 Squareness of cut ends 4 Tolerances on form 4.1 General 4.2 Straightness Figure 3 — Measurement of the deviation from straightness |
| 12 | Table 5 — Straightness tolerances 4.3 Convexity–Concavity Figure 4 — Measurement of convexity – concavity |
| 13 | Table 6 — Convexity – concavity tolerances 4.4 Twist Figure 5 — Measurement of twist |
| 14 | Table 7 — Twist tolerances 4.5 Angularity Figure 6 — Measurement of deviation from square |
| 15 | Table 8 — Squareness tolerances for square and rectangular tube 4.6 Corner and fillet radii 4.7 Depth of dents for round tubes |
| 16 | Table 9 — Depth of dents tolerances for round tube |
| 17 | Annex A (informative) Wall thickness variation (eccentricity) A.1 General A.2 Specifying round tube sizes and tolerances A.2.1 General Figure A.1 — Minimum and maximum values of the tube wall thickness A.2.2 Wall thickness variation for tubes specified as OD × t or ID × t |
| 18 | A.2.3 Wall thickness variation for tubes specified as OD × ID |
| 19 | Bibliography |
Related products
-
BS EN 754-8:2016 – TC:2020 Edition
Tracked Changes. Aluminium and aluminium alloys. Cold drawn rod/bar and tube – Porthole tubes, tolerances…
