{"id":81124,"date":"2024-10-17T18:51:31","date_gmt":"2024-10-17T18:51:31","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/ieee-c37-63-2005\/"},"modified":"2024-10-24T19:45:45","modified_gmt":"2024-10-24T19:45:45","slug":"ieee-c37-63-2005","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/ieee\/ieee-c37-63-2005\/","title":{"rendered":"IEEE C37.63 2005"},"content":{"rendered":"
Revision Standard – Active. Required definitions (for cutout type sectionalizers), ratings, procedures for performing design tests and production tests, constructional requirements, and application considerations for overhead and pad-mounted, dry-vault, and submersible automatic line sectionalizers for ac systems are specified.<\/p>\n
PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
---|---|---|---|---|---|---|---|
2<\/td>\n | Title Page <\/td>\n<\/tr>\n | ||||||
4<\/td>\n | Introduction Notice to users Errata Interpretations <\/td>\n<\/tr>\n | ||||||
5<\/td>\n | Patents Participants <\/td>\n<\/tr>\n | ||||||
7<\/td>\n | CONTENTS <\/td>\n<\/tr>\n | ||||||
9<\/td>\n | 1. Overview 1.1 Scope 1.2 Purpose 2. Normative references <\/td>\n<\/tr>\n | ||||||
11<\/td>\n | 3. Definitions 4. Service conditions 4.1 Usual service conditions <\/td>\n<\/tr>\n | ||||||
12<\/td>\n | 4.2 Unusual service conditions 5. Ratings 5.1 Ratings information <\/td>\n<\/tr>\n | ||||||
13<\/td>\n | 5.2 Rated power frequency 5.3 Rated maximum voltage and rated withstand voltage <\/td>\n<\/tr>\n | ||||||
14<\/td>\n | 5.4 Preferred continuous and load switching current ratings <\/td>\n<\/tr>\n | ||||||
16<\/td>\n | 5.5 Preferred minimum actuating current ratings (series coil sectionalizers) 5.6 Preferred short-circuit withstand current ratings <\/td>\n<\/tr>\n | ||||||
17<\/td>\n | 5.7 Preferred control voltage ratings <\/td>\n<\/tr>\n | ||||||
18<\/td>\n | 5.8 Preferred line charging and cable charging current ratings 6. Design tests 6.1 General conditions for tests 6.2 Withstand voltage tests 6.3 Continuous current tests <\/td>\n<\/tr>\n | ||||||
19<\/td>\n | 6.4 Switching tests 6.5 Short-time withstand current tests 6.6 Fault-making current tests 6.7 Condition of the sectionalizer after switching tests, short-time withstand 6.8 Mechanical operation tests <\/td>\n<\/tr>\n | ||||||
20<\/td>\n | 6.9 Radio influence voltage (RIV) tests <\/td>\n<\/tr>\n | ||||||
21<\/td>\n | 6.10 Partial discharge tests <\/td>\n<\/tr>\n | ||||||
22<\/td>\n | 6.11 Operating duty tests <\/td>\n<\/tr>\n | ||||||
24<\/td>\n | 6.12 Minimum actuating current tests <\/td>\n<\/tr>\n | ||||||
25<\/td>\n | 7. Production tests (routine tests) 7.1 Operational calibration 8. Construction requirements 8.1 Nameplate <\/td>\n<\/tr>\n | ||||||
26<\/td>\n | 8.2 Indicators 8.3 Accessories <\/td>\n<\/tr>\n | ||||||
27<\/td>\n | 8.4 Instruction 8.5 Conductor terminal 8.6 Tank construction <\/td>\n<\/tr>\n | ||||||
28<\/td>\n | Annex A (informative) X\/R ratios <\/td>\n<\/tr>\n | ||||||
30<\/td>\n | Annex B (normative) Ratings for series coil sectionalizers <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" IEEE Standard Requirements for Overhead, Pad-Mounted, Dry-Vault, and Submersible Automatic Line Sectionalizers for AC Systems<\/b><\/p>\n |