Revision Standard – Active. Revision of IEEE Std 1017-1991 Procedures and test voltage values for acceptance and maintenance testing of electrical submersible pump (ESP) cable systems are presented. This recommended practice applies to cable systems rated 3 kV and 5 kV (phase to phase) and is intended only for this special-purpose cable. The intent is to provide uniform test procedures and guidelines for evaluation of the test results.<\/p>\n
| PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
|---|---|---|---|---|---|---|---|
| 1<\/td>\n | Front Cover \n <\/td>\n<\/tr>\n | ||||||
| 5<\/td>\n | Introduction Notice to users Participants <\/td>\n<\/tr>\n | ||||||
| 7<\/td>\n | Contents <\/td>\n<\/tr>\n | ||||||
| 9<\/td>\n | IEEE Recommended Practice for Field Testing Electric Submersible Pump Cable 1. Overview 1.1 Scope <\/td>\n<\/tr>\n | ||||||
| 10<\/td>\n | 1.2 Purpose 2. Normative references 3. Definitions 3.1 absorption current: Current resulting from charge absorbed into the dielectric as a result of… <\/td>\n<\/tr>\n | ||||||
| 11<\/td>\n | 3.2 ac test: This test is performed by the manufacturer as a pass\/fail test to ensure the electri… 3.3 acceptance test: This test is intended to detect damage before the initial installation of ne… 3.4 capacitance current: Current required to charge the capacitor formed by the dielectric of the… 3.5 dc test: This test is performed by the manufacturer to ensure the electrical integrity of the… 3.6 electric submersible pumps (ESPs): Equipment that refers to electric-driven, deep-well centri… <\/td>\n<\/tr>\n | ||||||
| 12<\/td>\n | 3.7 ESP cable: Three-conductor power cable is installed in the well for the purpose of transmitti… 3.8 factory test: This test is completed by the manufacture at the 100% level. This voltage test … 3.9 field: This term or the term \u201cin the field\u201d\u009d may include cable not yet installed or cable that… 3.10 insulation resistance (IR): The opposition to current flow through the insulation. 3.11 insulation resistance test: By impressing a dc voltage across the insulation, a leakage curr… 3.12 leakage current (conductance): Current resulting from leakage through the cable insulating m… 3.13 maintenance test: This test is made after removing the cable from a well and is normally per… 3.14 motor lead extension cable: Three-conductor cable normally designed with a high-temperature\/… 3.15 rated voltage: This term is expressed for phase-to-phase voltage of a three-phase system. 3.16 surface connection cable: Power cable connecting the ESP cable to surface equipment. Sometim… <\/td>\n<\/tr>\n | ||||||
| 13<\/td>\n | 4. Safety 4.1 Description 4.2 Application 4.3 Procedures to secure cable and area <\/td>\n<\/tr>\n | ||||||
| 14<\/td>\n | 5. General considerations 5.1 Environmental influences 5.2 Test equipment <\/td>\n<\/tr>\n | ||||||
| 15<\/td>\n | 5.3 Equipment setup 5.4 Special fault-locating test equipment 5.5 Equipment maintenance <\/td>\n<\/tr>\n | ||||||
| 16<\/td>\n | 6. DC high-pot test methods 6.1 Precautions 6.2 Procedures <\/td>\n<\/tr>\n | ||||||
| 21<\/td>\n | 7. Evaluation of dc high-pot test results 7.1 Current-time relationship 7.2 Interpretation <\/td>\n<\/tr>\n | ||||||
| 24<\/td>\n | 7.3 Dielectric failure 7.4 Current comparison <\/td>\n<\/tr>\n | ||||||
| 25<\/td>\n | 8. Conductor resistivity and continuity tests 9. Mechanical integrity 10. Testing of surface feedthroughs and connections 10.1 Description <\/td>\n<\/tr>\n | ||||||
| 26<\/td>\n | 10.2 Wellhead with feedthrough 10.3 Wellhead with connections 10.4 Test procedure <\/td>\n<\/tr>\n | ||||||
| 27<\/td>\n | 10.5 Visual inspection 10.6 Procedure <\/td>\n<\/tr>\n | ||||||
| 28<\/td>\n | Annex A (informative) Bibliography <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" IEEE Recommended Practice for Field Testing Electric Submersible Pump Cable<\/b><\/p>\n |