NY StateFuelGasCode 2020 TEMP
$53.35
Fuel Gas Code of New York State
| Published By | Publication Date | Number of Pages |
| NY | 2020 | 186 |
This is a fully integrated custom code based on the 2018 International Fuel Gas Code.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | Cover |
| 2 | Copyright |
| 3 | ACKNOWLEDGEMENTS |
| 5 | PREFACE |
| 7 | EFFECTIVE USE |
| 9 | TABLE OF CONTENTS |
| 10 | APPENDIX B SIZING OF VENTING SYSTEMS SERVING APPLIANCES EQUIPPED WITH DRAFT HOODS, CATEGORY |
| 11 | CHAPTER 1 SCOPE AND ADMINISTRATION Section 101 Title, Scope and Purpose |
| 12 | 102 Applicability |
| 13 | 103 Administration and Enforcement |
| 14 | 104 Materials, Equipment and Methods of Construction |
| 15 | 105 Building Permits, Construction Inspections, Stop Work Orders, and Certificates of Occupancy |
| 16 | 106 Submittal Documents |
| 17 | 107 Service Utilities |
| 19 | CHAPTER 2 DEFINITIONS Section 201 General 202 General Definitions |
| 27 | CHAPTER 3 GENERAL REGULATIONS Section 301 General |
| 28 | 302 Structural Safety 303 Appliance Location |
| 29 | 304 Combustion, Ventilation and Dilution Air |
| 32 | 305 Installation |
| 33 | 306 Access and Service Space |
| 35 | 307 Condensate Disposal 308 Clearance Reduction |
| 36 | 309 Electrical 310 Electrical Bonding |
| 39 | CHAPTER 4 GAS PIPING INSTALLATIONS Section 401 General 402 Pipe Sizing |
| 40 | 403 Piping Materials |
| 79 | 404 Piping System Installation |
| 81 | 405 Piping Bends and Changes in Direction |
| 82 | 406 Inspection, Testing and Purging |
| 84 | 407 Piping Support 408 Drips and Sloped Piping |
| 85 | 409 Shutoff Valves 410 Flow Controls |
| 86 | 411 Appliance and Manufactured Home Connections |
| 87 | 412 Liquefied Petroleum Gas Motor Vehicle Fuel-dispensing Facilities |
| 89 | 413 Compressed Natural Gas Motor Vehicle Fuel-dispensing Facilities |
| 90 | 414 Supplemental and Standby Gas Supply 415 Piping Support Intervals |
| 91 | 416 Overpressure Protection Devices |
| 93 | CHAPTER 5 CHIMNEYS AND VENTS Section 501 General |
| 94 | 502 Vents |
| 95 | 503 Venting of Appliances |
| 104 | 504 Sizing of Category I Appliance Venting Systems |
| 108 | 505 Direct-vent, Integral Vent, Mechanical Vent and Ventilation/Exhaust Hood Venting |
| 109 | 506 Factory-built Chimneys |
| 131 | CHAPTER 6 SPECIFIC APPLIANCES Section 601 General 602 Decorative Appliances for Installation in Fireplaces 603 Log Lighters 604 Vented Gas Fireplaces (Decorative Appliances 605 Vented Gas Fireplace Heaters 606 Incinerators and Crematories 607 Commercial-industrial Incinerators 608 Vented Wall Furnaces 609 Floor Furnaces |
| 132 | 610 Duct Furnaces 611 Nonrecirculating Direct-fired Industrial Air Heaters |
| 133 | 612 Recirculating Direct-fired Industrial Air Heaters 613 Clothes Dryers 614 Clothes Dryer Exhaust |
| 135 | 615 Sauna Heaters 616 Engine and Gas Turbine-powered Equipment |
| 136 | 617 Pool and Spa Heaters 618 Forced-air Warm-air Furnaces 619 Conversion Burners |
| 137 | 620 Unit Heaters 621 Unvented Room Heaters 622 Vented Room Heaters 623 Cooking Appliances |
| 138 | 624 Water Heaters 625 Refrigerators 626 Gas-fired Toilets 627 Air-conditioning Appliances |
| 139 | 628 Illuminating Appliances 629 Small Ceramic Kilns 630 Infrared Radiant Heaters |
| 140 | 631 Boilers 632 Equipment Installed in Existing Unlisted Boilers 633 Stationary Fuel-cell Power Systems 634 Chimney Damper Opening Area 635 Gaseous Hydrogen Systems 636 Outdoor Decorative Appliances |
| 141 | CHAPTER 7 GASEOUS HYDROGEN SYSTEMS Section 701 General 702 General Definitions 703 General Requirements |
| 142 | 704 Piping, Use and Handling |
| 143 | 705 Testing of Hydrogen Piping Systems |
| 144 | 706 Location of Gaseous Hydrogen Systems 707 Operation and Maintenance of Gaseous Hydrogen Systems 708 Design of Liquefied Hydrogen Systems Associated with Hydrogen Vaporization Operations |
| 145 | CHAPTER 8 REFERENCED STANDARDS |
| 151 | APPENDIX A SIZING AND CAPACITIES OF GAS PIPING |
| 161 | APPLIANCES AND APPLIANCES LISTED FOR USE WITH TYPE B VENTS |
| 171 | APPENDIX C EXIT TERMINALS OF MECHANICAL DRAFT AND DIRECT-VENT VENTING SYSTEMS |
| 173 | APPENDIX D RECOMMENDED PROCEDURE FOR SAFETY INSPECTION OF AN EXISTING APPLIANCE INSTALLATION |
| 179 | INDEX |
