ISO 7973:1992
$19.50
Cereals and milled cereal products — Determination of the viscosity of flour — Method using an amylograph
| Published By | Publication Date | Number of Pages |
| ISO | 1992-12 | 12 |
The method is based on preparation of a suspension of flour in water, followed by recording of the viscosity of the suspension which is heated at a constant rate from 30 °C to the temperature corresponding to the moment at which viscosity starts to decrease, having reached its maximum (approximately 95 °C). Applies to wheat and rye flour and also to wheat and rye grain.
Related products
-
ISO 1992-2:1973/Amd 1:1979
Commercial refrigerated cabinets — Methods of test — Part 2: General test conditions — Amendment…
-
ISO 3973:1996
Living animals for slaughter — Vocabulary — Bovines Published By Publication Date Number of Pages…
-
ISO 8973:1997
Gaz de pétrole liquéfiés — Méthode de calcul de la masse volumique et de la…
-
BS EN 60598-2-6:1995
Luminaires. Particular requirements – Luminaires with built-in transformers for filament lamps Published By Publication Date…
-
ISO 2562:1973/Amd 1:1982
Modular units for machine tool construction — Slide units — Amendment 1 Published By Publication…
-
BS 308-2:1985
Engineering drawing practice – Recommendations for dimensioning and tolerancing of size Published By Publication Date…
-
BS 6148-3:1981
Methods of test for commercial refrigerated cabinets – Determination of temperature Published By Publication Date…
-
BS EN ISO 8973:1999
Liquefied petroleum gases. Calculation method for density and vapour pressure Published By Publication Date Number…
-
BS EN ISO 1973:1996
Textile fibres. Determination of linear density. Gravimetric method and vibroscope method Published By Publication Date…
-
BS EN 27963:1992
Specification for calibration block No. 2 for ultrasonic examination of welds Published By Publication Date…
-
BS 4317-32:1996
Methods of test for cereals and pulses – Determination of bulk density of cereals, called…
-
ISO 973:1999
Pimento (allspice) [Pimenta dioica (L.) Merr.], whole or ground — Specification Published By Publication Date…
-
ISO 1992-3:1973
Commercial refrigerated cabinets — Methods of test — Part 3: Temperature test Published By Publication…
-
ISO 7913:1994
Aéronautique et espace — Vis métriques — Tolérances de forme et de position Published By…
-
BS EN ISO 7973:2015:2016 Edition
Cereals and milled cereal products. Determination of the viscosity of flour. Method using an amylograph…
-
BS EN 22592:1994
Methods of test for petroleum and its products. Petroleum products. Determination of flash and fire…
-
BS 308-3:1990
Engineering drawing practice – Recommendations for geometrical tolerancing Published By Publication Date Number of Pages…
-
BS EN 60598-2-6:1995
Luminaires. Particular requirements – Luminaires with built-in transformers for filament lamps Published By Publication Date…
-
BS 2782-1 Method 140B:1993
Methods of testing plastics. Thermal properties – Determination of the burning behaviour of flexible vertical…
-
BS 6222-1:1982
Domestic kitchen equipment – Specification for co-ordinating dimensions Published By Publication Date Number of Pages…
-
ISO 9773:1998/Amd 1:2003
Plastics — Determination of burning behaviour of thin flexible vertical specimens in contact with a…
-
BS 2000-432:1998
Methods of test for petroleum and its products – Liquefied petroleum gases. Calculation method for…
-
BS 4928:1985
Specification for man-made fibre ropes Published By Publication Date Number of Pages BSI 1985 16
-
BS 1841-1:1991
Rear-mounted, three-point linkage on agricultural wheeled tractors – Specification for categories 1, 2 and 3…
-
ISO 7873:1993
Control charts for arithmetic average with warning limits Published By Publication Date Number of Pages…
-
BS EN ISO 7083:2021 – TC
Tracked Changes. Technical product documentation. Symbols used in technical product documentation. Proportions and dimensions Published…
-
BS EN ISO 6272:1994:1995 Edition
Paints and varnishes. Falling-weight test Published By Publication Date Number of Pages BSI 1995 16
-
ISO 2912:1973/Amd 1:1982
Modular units for machine tool construction — Multi-spindle heads — Casing and input drive shaft…
-
BS 2A 296:1995
Bolts and screws, metric. Tolerances of form and position Published By Publication Date Number of…
-
ISO 1992-2:1973
Commercial refrigerated cabinets — Methods of test — Part 2: General test conditions Published By…
-
BS ISO/IEC 9973:1994:1995 Edition
Information technology. Computer graphics and image processing. Procedures for registration of graphical items Published By…
-
BS EN ISO 9773:1999:2004 Edition
Plastics. Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame…
-
ISO 1973:1995
Textile fibres — Determination of linear density — Gravimetric method and vibroscope method Published By…
-
ISO 9773:1998
Plastics — Determination of burning behaviour of thin flexible vertical specimens in contact with a…
-
BS EN ISO 8973:1999+A1:2020
Liquefied petroleum gases. Calculation method for density and vapour pressure Published By Publication Date Number…
-
CSA W178.1-18:2018 Edition
Certification of welding inspection organizations Published By Publication Date Number of Pages CSA 2018-05-01 24
-
BS 4929-1:1973
Specification for steel hexagon prevailing-torque type nuts – Metric series Published By Publication Date Number…
-
ISO 1992-3:1973/Amd 1:1980
Commercial refrigerated cabinets — Methods of test — Part 3: Temperature test — Amendment 1…
-
JIS K 2240:2013
Liquefied Petroleum Gases Published By Publication Date Number of Pages JIS 2013-03-21 125
-
BS 4370-2:1993:2001 Edition
Methods of test for rigid cellular materials – Methods 7 to 9 Published By Publication…
