ISO 393-4:1986
$18.85
Asbestos-cement products — Part 4: Trapezoidal section sheets for roofing and cladding
| Published By | Publication Date | Number of Pages |
| ISO | 1986-07 | 14 |
Specifies requirememts for asbestos-cement trapezoidal section sheets used mainly for roofing and cladding. It also specifies test methods to check conformity with these requirements, together with requirements for marking and acceptance conditions. It does not apply to corrugated sheets, to asymmetrical section corrugated sheets or to corrugated or asymmetrical section "short sheets", which are covered as indicated in clause 0.
Related products
-
BS 4360:1979:1982 Edition
Specification for weldable structural steels Published By Publication Date Number of Pages BSI 1982 50
-
BS 6665:1985
Method for determination of density or relative density of liquefied petroleum gases and other light…
-
BS 308-3:1990
Engineering drawing practice – Recommendations for geometrical tolerancing Published By Publication Date Number of Pages…
-
BS 2782-8 Method 830A:1986
Methods of testing plastics. Other properties – Determination of the effects of liquid chemicals, including…
-
BS 6897-1:1987
Experimental determination of mechanical mobility. – Specification for transducers Published By Publication Date Number of…
-
BS 7080-2:1989
Guide to construction and use of 6.30 mm (0.25 in) magnetic tape cartridge using GCR…
-
BS 6292:1982
Method for evaluation of performance of rotary pneumatic assembly tools for threaded fasteners Published By…
-
BS 5600-4.17.4:1986
Powder metallurgical materials and products. Methods of testing and chemical analysis of hardmetals. Chemical analysis…
-
BS 7020-13:1988:1989 Edition
Analysis of iron ores – Method for the determination of arsenic content. Spectrophotometric method Published…
-
BS 1972:1967:1983 Edition
Specification for polythene pipe (Type 32) for above ground use for cold water services Published…
-
IEEE 802.3u-1995
IEEE Standards for Local and Metropolitan Area Networks: Supplement – Media Access Control (MAC) Parameters,…
-
BS 5381-2:1988
Methods for determination of physical properties of tobacco and tobacco products – Nominal diameter of…
-
BS 5600-2-2.3:1988
Powder metallurgical materials and products. Methods of sampling and testing metallic powders – Determination of…
-
BS 7020-12:1988:1989 Edition
Analysis of iron ores – Method for the determination of titanium content: spectrophotometric method Published…
-
BS 3939-7:1985
Graphical symbols for electrical power, telecommunications and electronics diagrams – Switchgear, controlgear and protective devices…
-
BS 7080-1:1989
Guide to construction and use of 6.30 mm (0.25 in) magnetic tape cartridge for data…
-
BS 690-2:1981
Asbestos-cement slates and sheets – Specification for asbestos-cement and cellulose-asbestos-cement flat sheets Published By Publication…
-
BS 6846:1987
Specification for rubber hoses and hose assemblies for use in oil burners Published By Publication…
-
BS 4942-1:1981
Short link chain for lifting purposes – Specification for general conditions of acceptance Published By…
-
BS 7034-1:1988:1989 Edition
Viscosity and viscometric fixed points of glass – Recommendations for use in the determination of…
-
BS 6829-2.3:1989
Analysis of surface active agents (raw materials). Alkane sulphonates – Method for determination of alkane…
-
ISO 393-2:1986
Asbestos-cement products — Part 2: Asbestos-cement-cellulose corrugated sheets and fittings for roofing and cladding Published…
-
BS 1902-3-3.8:1989
Methods of testing refractory materials. General and textural properties – Determination of bulk density, true…
-
BS EN ISO 3993:1996
Liquefied petroleum gas and light hydrocarbons. Determination of density or relative density. Pressure hydrometer method…
-
BSI PD 2777:1994:2003 Edition
Fabric flammability and burning accidents Published By Publication Date Number of Pages BSI 2003 28
-
BS 6049-6:1988
Methods of test for tea – Determination of acid-insoluble ash Published By Publication Date Number…
-
BS 6783-1:1986
Sampling and analysis of nickel, ferronickel and nickel alloys – Method for determination of silver,…
-
BS 6623-3:1986
DTE/DCE interface connectors and pin assignments – Specification for 15-pin connector [identical with ISO/DIS 4903…
-
BS 6068-2-2.23:1986
Water quality. Physical, chemical and biochemical methods – Method for the determination of anionic surfactants…
-
BS 4993-6:1980
Methods of test for aluminium fluoride for industrial use – Determination of moisture content (gravimetric…
-
ASTM-D4703 2010
D4703-10 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets Published…
-
BS 7020-17:1988:1989 Edition
Analysis of iron ores – Method for the determination of lead and/or zinc contents: flame…
-
BS 3790:1995
Specification for endless wedge belt drives and endless V-belt drives Published By Publication Date Number…
-
BS EN 20534:1993:1989 Edition
Method for determination of thickness and apparent bulk density or apparent sheet density of paper…
-
ASTM-D4703 2007
D4703-07 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets Published…
-
BS EN 253:2019
District heating pipes. Bonded single pipe systems for directly buried hot water networks. Factory made…
-
BS EN ISO 7393-2:2000
Water quality. Determination of free chlorine and total chlorine – Colorimetric method using N,N-diethyl-1,4-phenylenediamine for…
-
BS 6393:1987
Specification for calibration of stylus instruments Published By Publication Date Number of Pages BSI 1987…
-
BS 3762-3-3.3:1987
Analysis of formulated detergents – Quantitative test methods – Method for determination of hydrolyzable and…
-
BS 6911-10:1996:2006 Edition
Testing earth-moving machinery – Machine-mounted retrieval device. Performance requirements Published By Publication Date Number of…
