BSI PD CEN/TS 1452-7:2014
$142.49
Plastics piping systems for water supply and for buried and above-ground drainage and sewerage under pressure. Unplasticized poly(vinyl chloride) (PVC-U) – Guidance for the assessment of conformity
| Published By | Publication Date | Number of Pages |
| BSI | 2014 | 30 |
This part of EN ISO 1452 gives guidance for the assessment of conformity of compounds/formulations, products, joints and assemblies in accordance with the applicable parts of EN ISO 1452 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of certification procedures.
NOTE 1 It is recommended that the quality management system conforms to or is no less stringent than the relevant requirements to EN ISO 9001 [1].
NOTE 2 If certification is involved, the certification body and inspection body is preferably compliant with EN ISO/IEC 17065 [5] or EN ISO/IEC 17021 [3], as applicable.
In conjunction with Parts 1 to 5 of EN ISO 1452 (see Foreword) this document is applicable to unplasticized poly(vinyl chloride) (PVC-U) plastics piping systems for water supply and for buried and above -ground drainage and sewerage under pressure.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 4 | Contents Page |
| 5 | Foreword |
| 6 | Introduction Figure 1 — Typical scheme for the assessment of conformity by a manufacturer Figure 2 — Typical scheme for the assessment of conformity by a manufacturer, including a certification |
| 7 | 1 Scope 2 Normative references 3 Terms and definitions |
| 11 | 4 Abbreviated terms 5 General 6 Testing and inspection 6.1 Grouping 6.1.1 General |
| 12 | 6.1.2 Size groups Table 1 — Size groups 6.1.3 Fitting/valve groups Table 2 — Fitting/valve groups 6.2 Type tests (TTs) |
| 13 | Table 3 — Compound/formulation specification |
| 14 | Table 4 — Characteristics of compound/formulation that require type testing (TT) Table 5 — Characteristics of pipes that require type testing (TT) |
| 16 | Table 6 — Characteristics of fittings and valves that require type testing (TT) |
| 18 | Table 7 — Characteristics of fitness for purpose of the system that require type testing (TT) 6.3 Batch release tests (BRTs) |
| 19 | Table 8 — Characteristics of compound/formulation and minimum sampling frequencies for BRTs by the raw material manufacturer Table 9 — Characteristics of pipes and minimum sampling frequencies for BRTs by the pipe manufacturer |
| 20 | Table 10 — Characteristics of fittings and valves and minimum sampling frequencies for BRTs by the fitting/valve manufacturer 6.4 Process verification tests (PVTs) |
| 21 | Table 11 — Characteristics of compound and minimum sampling frequencies for PVTs Table 12 — Characteristics of pipes and minimum sampling frequencies for PVTs Table 13 — Characteristics of fittings and valves and minimum sampling frequencies for PVTs |
| 22 | Table 14 — Characteristics of fitness for purpose of the system and minimum sampling frequencies for PVTs 6.5 Audit tests (ATs) Table 15 — Characteristics of compounds/formulations and minimum sampling frequencies for ATs |
| 23 | Table 16 — Characteristics of pipes and minimum sampling frequencies for ATs |
| 24 | Table 17 — Characteristics of fittings and valves and minimum sampling frequencies for ATs |
| 25 | Table 18 — Characteristics of fitness for purpose of the system and minimum sampling frequencies for ATs 6.6 Indirect tests (ITs) 6.7 Test records |
| 26 | Annex A (informative) Basic test Matrix for PVC-U Water and Pressure Sewer piping components Table A.1 — Basic test matrix for PVC-U Water and Pressure Sewer piping components |
| 28 | Bibliography |
