BS EN ISO 19932-1:2013
$142.49
Equipment for crop protection. Knapsack sprayers – Safety and environmental requirements
| Published By | Publication Date | Number of Pages |
| BSI | 2013 | 28 |
This part of ISO 19932 specifies the safety and environmental requirements and their means of verification for the design and construction of knapsack sprayers carried on the back or shoulder of the operator for use with plant protection products. In addition, it specifies the type of information on safe working practices (including residual risks) to be provided by the manufacturer.
It is applicable to lever-operated knapsack sprayers, knapsack compression sprayers and knapsack sprayers driven by an engine or electric motor using hydraulic pressure atomisation of the spray liquid, with a nominal volume of more than 3 l, for their intended use primarily in agriculture and horticulture.
It does not apply to knapsack mistblowers according to ISO 28139.
This part of ISO 19932 deals with all significant hazards, hazardous situations and hazardous events relevant to knapsack sprayers when they are used as intended and under conditions of misuse which are reasonably foreseeable by the manufacturer (see Annex A), excepting the hazards arising from:
-
static electricity;
-
explosion or fire from chemicals for spraying; and
-
insufficient structural integrity.
This document is not applicable to knapsack sprayers which are manufactured before the date of publication of this document.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 5 | Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC on machinery and Directive 2009/127/EC amending Directive 2006/42/EC with regard to machinery for pesticide application |
| 7 | Foreword |
| 8 | Introduction |
| 10 | Section sec_1 Section sec_2 1 Scope 2 Normative references |
| 11 | Section sec_3 Section sec_3.1 Section sec_3.2 Section sec_3.3 Section sec_4 Section sec_4.1 Section sec_4.1.1 3 Terms and definitions 4 General requirements 4.1 General |
| 12 | Section sec_4.1.2 Section sec_4.1.3 Section sec_4.1.4 Section sec_4.1.5 Section sec_4.1.6 Section sec_4.1.7 Section sec_4.1.8 Section sec_4.1.9 Section sec_4.1.10 |
| 13 | Section sec_4.1.11 Section sec_4.1.12 Section sec_4.2 Section sec_4.2.1 Section sec_4.2.2 Section sec_4.2.3 Section sec_4.2.4 Section sec_4.2.5 Section sec_4.3 Section sec_4.3.1 4.2 Harness 4.3 Spray tank |
| 14 | Section sec_4.3.2 Section sec_4.3.3 Section sec_4.3.4 Section sec_4.3.5 Section sec_4.3.6 Section sec_4.4 Section sec_4.4.1 Section sec_4.4.2 Section sec_4.4.3 Section sec_4.4.4 4.4 Controls |
| 15 | Section sec_4.5 Section sec_4.5.1 Section sec_4.5.2 Section sec_4.5.3 Section sec_4.6 Section sec_4.6.1 Section sec_4.6.2 Section sec_4.7 Section sec_4.7.1 Section sec_4.7.2 Section sec_4.7.3 4.5 Hoses 4.6 Filters 4.7 Spray lance and nozzles |
| 16 | Section sec_4.7.4 Section sec_4.7.5 Section sec_4.7.6 Section sec_5 Section sec_5.1 Section sec_5.1.1 Section sec_5.1.2 Section sec_5.2 Section sec_5.2.1 Section sec_5.2.2 Section sec_5.2.3 Section sec_5.2.4 5 Specific requirements for lever-operated knapsack sprayers 5.1 General 5.2 Spray tank |
| 17 | Section sec_5.2.5 Section sec_6 Section sec_6.1 Section sec_6.1.1 Section sec_6.2 Section sec_6.2.1 Section sec_6.2.2 Section sec_6.2.3 Section sec_6.2.4 Section sec_6.2.5. Section sec_6.2.6 Section sec_6.3 Section sec_6.3.1 6 Specific requirements for engine- or motor-driven knapsack sprayers 6.1 General 6.2 Spray tank 6.3 Controls |
| 18 | Section sec_6.3.2 Section sec_6.4 Section sec_6.5 Section sec_6.5.1 Section sec_6.5.2 Section sec_6.5.3 Section sec_6.6 6.4 Power-driven components 6.5 Fuel tank 6.6 Hot parts |
| 19 | Figure fig_1 Section sec_6.7 Section sec_6.8 Section sec_6.9 Section sec_6.10 Section sec_6.11 6.7 Exhaust system 6.8 Parts under high voltage 6.9 Electromagnetic immunity 6.10 Noise 6.11 Vibration |
| 20 | Section sec_7 Section sec_7.1 Section sec_7.1.1 Section sec_7.1.2 Section sec_7.2 Section sec_7.3 Section sec_7.3.1 Section sec_7.3.2 Section sec_7.3.3 7 Specific requirements for compression sprayers 7.1 General 7.2 Harness 7.3 Spray tank |
| 21 | Section sec_8 Section sec_8.1 Section sec_8.1.1 8 Information for use 8.1 Instruction handbook |
| 23 | Section sec_8.1.2 Section sec_8.1.2.1 Section sec_8.1.2.2 Section sec_8.2 8.2 Marking |
| 24 | Section sec_8.3 8.3 Warnings |
| 25 | Annex sec_A Table tab_A.1 Annex A (informative) List of significant hazards |
| 26 | Reference ref_1 Reference ref_2 Reference ref_3 Reference ref_4 Reference ref_5 Bibliography |
