BS EN ISO 11297-3:2013:2014 Edition
$142.49
Plastics piping systems for renovation of underground drainage and sewerage networks under pressure – Lining with close-fit pipes
| Published By | Publication Date | Number of Pages |
| BSI | 2014 | 26 |
This part of ISO 11297, in conjunction with ISO 11297-1, specifies requirements and test methods for close-fit lining systems intended to be used for the renovation of underground drainage and sewerage networks under pressure. It is applicable to pipes and fittings, as manufactured, as well as to the installed lining system. It is applicable to polyethylene (PE) pipe for both independent and interactive pressure pipe liners as well as associated fittings and joints for the construction of the lining system.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | Foreword |
| 7 | Introduction |
| 8 | Figure fig_1 |
| 9 | Section sec_1 Section sec_2 1 Scope 2 Normative references |
| 10 | Section sec_3 Section sec_3.1 Section sec_3.1.1 Section sec_3.1.2 Section sec_3.2 Section sec_3.3 Section sec_3.3.1 Section sec_3.3.2 Section sec_3.3.3 Section sec_3.4 Section sec_3.4.1 Section sec_3.5 3 Terms and definitions 3.1 General 3.2 Techniques 3.3 Characteristics 3.4 Materials 3.5 Product stages |
| 11 | Section sec_3.6 Section sec_3.6.1 Section sec_3.6.2 Section sec_3.7 Section sec_3.7.1 Section sec_3.7.2 Section sec_3.7.3 Section sec_3.7.4 3.6 Service conditions 3.7 Joints |
| 12 | Section sec_4 Section sec_4.1 Section sec_4.2 Section sec_5 Section sec_5.1 Section sec_5.1.1 Table tab_1 Section sec_5.1.2 4 Symbols and abbreviated terms 4.1 Symbols 4.2 Abbreviated terms 5 Pipes at the “M” stage 5.1 Materials |
| 13 | Section sec_5.2 Section sec_5.2.1 Section sec_5.2.2 Section sec_5.3 Section sec_5.4 Section sec_5.5 Table tab_2 Section sec_5.6 Section sec_5.7 Section sec_5.8 5.2 General characteristics 5.3 Material characteristics 5.4 Geometric characteristics 5.5 Mechanical characteristics 5.6 Physical characteristics 5.7 Jointing 5.8 Marking |
| 14 | Section sec_6 Section sec_7 Section sec_8 Section sec_8.1 Section sec_8.2 Section sec_8.3 Section sec_8.4 6 Fittings at the “M” stage 7 Ancillary components 8 Fitness for purpose of the installed lining system at the “I” stage 8.1 Materials 8.2 General characteristics 8.3 Material characteristics 8.4 Geometric characteristics |
| 15 | Table tab_3 Section sec_8.5 8.5 Mechanical characteristics |
| 16 | Table tab_4 Section sec_8.6 Section sec_8.7 8.6 Physical characteristics 8.7 Additional characteristics |
| 17 | Section sec_8.8 Section sec_9 Section sec_9.1 Section sec_9.2 Section sec_9.3 Section sec_9.3.1 Section sec_9.3.2 8.8 Sampling 9 Installation practice 9.1 Preparatory work 9.2 Storage, handling and transport of pipes and fittings 9.3 Equipment |
| 18 | Section sec_9.3.3 Section sec_9.3.4 Section sec_9.3.5 Section sec_9.3.6 Section sec_9.3.7 Section sec_9.3.8 |
| 19 | Section sec_9.3.9 Section sec_9.4 9.4 Installation |
| 20 | Section sec_9.5 9.5 Process-related inspection and testing |
| 21 | Annex sec_A Annex sec_A.1 Annex sec_A.2 Figure fig_A.1 Annex sec_A.3 Annex sec_A.3.1 Annex sec_A.3.2 Annex A (normative) Factory-folded heat-reverted polyethylene (PE) pipe — Determination of memory ability |
| 22 | Table tab_A.1 Annex sec_A.3.3 Annex sec_A.4 |
| 23 | Reference ref_1 Reference ref_2 Bibliography |
