BS EN 60079-19:2011+A1:2015
$215.11
Explosive atmospheres – Equipment repair, overhaul and reclamation
| Published By | Publication Date | Number of Pages |
| BSI | 2015 | 74 |
This part of IEC 60079
-
gives instructions, principally of a technical nature, on the repair, overhaul, reclamation and modification of equipment designed for use in explosive atmospheres;
-
is not applicable to maintenance, other than when repair and overhaul cannot be disassociated from maintenance, neither does it give advice on cable entry systems which may require a renewal when the equipment is re-installed;
-
is not applicable to type of protection “m”, “o” and “q”; – assumes that good engineering practices are adopted throughout.
Much of the content of this standard is concerned with the repair and overhaul of electrical machines. This is not because they are the most important items of explosion-protected equipment, but rather because they are often major items of repairable capital equipment in which, whatever type of protection is involved, sufficient commonality of construction exists as to make possible more detailed instructions for their repair, overhaul, reclamation or modification.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 9 | English CONTENTS |
| 14 | INTRODUCTION |
| 15 | 1 Scope 2 Normative references |
| 16 | 3 Terms and definitions |
| 18 | 4 General 4.1 General principles |
| 19 | 4.2 Statutory requirements for repair facility 4.3 Instructions for the user 4.4 Instructions for the repair facility |
| 28 | 5 Additional requirements for the repair and overhaul of equipment with type of protection “d” (flameproof) 5.1 Application 5.2 Repair and overhaul |
| 32 | 5.3 Reclamation |
| 34 | 5.4 Alterations and modifications 6 Additional requirements for the repair and overhaul of equipment with type of protection “i” (intrinsic safety) 6.1 Application |
| 35 | 6.2 Repair and overhaul |
| 38 | 6.3 Reclamation 6.4 Modifications 7 Additional requirements for the repair and overhaul of equipment with type of protection “p” (pressurized) 7.1 Application 7.2 Repair and overhaul |
| 42 | 7.3 Reclamation |
| 43 | 7.4 Alterations and modifications 8 Additional requirements for the repair and overhaul of equipment with type of protection “e” (increased safety) 8.1 Application |
| 44 | 8.2 Repair and overhaul |
| 49 | 8.3 Reclamation |
| 50 | 8.4 Modifications |
| 51 | 9 Additional requirements for the repair and overhaul of equipment with type of protection “n” 9.1 Application 9.2 Repair and overhaul |
| 56 | 9.3 Reclamation |
| 57 | 9.4 Alterations and modifications |
| 58 | 10 Additional requirements for the repair and overhaul of equipment covered by IEC 60079-26 11 Additional requirements for the repair and overhaul of equipment with type of protection Group III ‘t’ (formerly known as ‘tD’ or DIP) 11.1 Application 11.2 Repair and overhaul |
| 62 | 11.3 Reclamation |
| 63 | 11.4 Alterations and modifications 12 Additional requirements for the repair and overhaul of equipment with type of protection pressurization ’pD’ 12.1 Application 12.2 Repair and overhaul |
| 64 | Annex A (normative) Identification of repaired equipment by marking |
| 66 | Annex B (normative) Knowledge, skills and competencies of “responsible persons” and “operatives” |
| 68 | Annex C (normative) Requirements for measurements in flameproof equipment during overhaul, repair and reclamation (including guidance on tolerances) Table C.1 – Determination of maximum gap of reclaimed parts |
| 70 | Figure C.1 – Determination of maximum gap of reclaimed parts |
| 72 | Bibliography |
