BS EN 15094:2022 – TC:2023 Edition

$280.87

Tracked Changes. Safety of machinery. Safety requirements for cold flat rolling mills

Published By	Publication Date	Number of Pages
BSI	2023	208

Guaranteed Safe Checkout

Category: BSI

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

This document specifies the general safety requirements for cold rolling mills for flat products as defined in 3.1. This document is applicable to: Plant (machinery, equipment, devices according Annex D) used for the manufacturing of metal cold rolled flat products from the material supply from entry (1), via the mill stand(s) (2) with roll changing devices (4), to the material removal (3) (see Figure 1). [Figure 1] This document does not cover: — Design and construction of buildings including cellars and their facilities; — Thermo process equipment, e.g. in accordance with EN 746 series; — Strip processing lines according to EN 15061, e.g. pickling line; — Abrasive blasting plants according to EN 1248; — Coil transporting system before coil take-over-point at the entry section and after coil take-over-point at the exit section, e.g. hook conveyors, overhead cranes, fork lift and railway trucks and other vehicles; — Roll shop equipment; — Hook conveyors according to EN 619; — Non-fixed load lifting attachments, e.g. according to EN 13155; — Storage equipment (e.g. high-bay warehouses); — Cranes, fork lifts, trucks and railway trucks and other vehicles; — Process technology (e.g. systems for rolling lubricant, compressed air, treatment of water, cleaning system for exhaust air); — Firefighting system. NOTE 1 Special requirements for protection of persons in case of using asphyxiant gases used in firefighting system is covered by this document, see Annex C.

PDF Catalog

PDF Pages	PDF Title
130	National foreword
134	European foreword
135	Introduction
136	1 Scope
137	2 Normative references
139	3 Terms and definitions
144	4 Significant hazards and risk assessment 4.1 General 4.2 Interfaces to the linked/integrated equipment
145	5 Safety requirements and/or protective/risk reduction measures 5.1 General 5.2 General requirements for design, planning and risk assessment 5.2.1 General
146	5.2.2 Planning of rolling mills 5.2.3 Linked equipment
147	5.2.4 Structural assembly 5.2.5 Safety layout 5.2.6 Safety signs and warning devices
148	5.2.7 Personal protective equipment (PPE) 5.2.8 Loss of energy and failure of controls 5.2.9 Workstations and assigned modes of operation
149	5.2.10 Enabling control device and hold-to-run control device
150	5.2.11 Access to and presence in danger zones
153	5.2.12 Safeguarding 5.2.13 Guards 5.2.14 Sensitive protective equipment
154	5.2.15 Guard-rails 5.2.16 Preconditions for movements of equipment not causing significant hazards 5.2.17 Determination of required Performance Level (PLr)
155	5.2.18 Stored energy
156	5.2.19 Mechanical restraint devices 5.2.20 Electrical equipment 5.2.21 Safety-related control systems 5.2.22 Safety-related software and parameters
157	5.2.23 Remote access to the control systems 5.2.24 Radiation and fields
158	5.2.25 Fluid systems (hydraulic, pneumatic, cooling, lubrication and additional media systems)
159	5.2.26 Substances 5.2.27 Firefighting 5.2.28 Ergonomics
160	5.2.29 Vibrations 5.2.30 Noise reduction as a safety requirement
162	5.3 Significant hazards, hazardous situations, safety requirements and/or protective/risk reduction measures 5.3.1 Structure and content of Table 4
179	6 Verification/validation of safety requirements/functions and/or protective/risk reduction measures 6.1 General
180	6.2 Required verification D 6.3 Required verification V, M and T
181	7 Information for use 7.1 General 7.2 Warning devices and safety signs 7.3 Minimum marking
182	7.4 Accompanying documents 7.4.1 Instructions
184	7.4.2 Information for transportation and assembly of the equipment 7.4.3 Information about disabling, disassembly and disposal of the equipment 7.5 Training of personnel
185	8 Supplementary information regarding repair work
186	Annex A (normative) Requirements for shut-down, emergency stop and other stop functions
191	Annex B (normative) Noise test code
196	Annex C (normative) Protection of persons in case of using asphyxiant gases used infirefighting systems
200	Annex D (informative) Machines and/or equipment covered by this document
202	Annex E (informative) Roll spalling
203	Annex F (informative) Example for modes of operation in relation to segregated areas
204	Annex G (informative) Example for the risk analysis due to interfaces
205	Bibliography

Additional information

Status	Definitive
Pages	208
Publication Date	2023-10-31
ISBN	978 0 539 23914 0
Standard Number	BS EN 15094:2022 – TC
Title	Tracked Changes. Safety of machinery. Safety requirements for cold flat rolling mills
Descriptors	Production equipment, Noise (environmental), Control equipment, Metalworking machines, Equipment safety, Safety measures, Rolling mills, Instructions for use, Metalworking, Hazards, Cold rolling, Occupational safety, Rolled products, Verification, Safety devices, Cold-working
Publisher	BSI
Committee	MCE/23
ICS Codes	77.180 - Equipment for the metallurgical industry

Preview PDF


PDF Format	Searchable	Printable	Preview Now

BS EN 15094:2022 – TC:2023 Edition

PDF Catalog

Related products