ASTM-D648 2007

$44.96

D648-07 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position

Published By	Publication Date	Number of Pages
ASTM	2007	13

Guaranteed Safe Checkout

Categories: 83.080.01 - Plastics in general, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

1.1 This test method covers the determination of the temperature at which an arbitrary deformation occurs when specimens are subjected to an arbitrary set of testing conditions.

1.2 This test method applies to molded and sheet materials available in thicknesses of 3 mm [1/8 in.] or greater and which are rigid or semirigid at normal temperature.

Note 1Sheet stock less than 3 mm [0.125 in.] but more than 1 mm [0.040 in.] in thickness may be tested by use of a composite sample having a minimum thickness of 3 mm. The laminae must be of uniform stress distribution. One type of composite specimen has been prepared by cementing the ends of the laminae together and then smoothing the edges with sandpaper. The direction of loading shall be perpendicular to the edges of the individual laminae.

1.3 The values stated in SI units are to be regarded as standard. The values given in brackets are for information only.

1.4 Due to the potential safety and environmental hazards associated with mercury-filled thermometers, the use of alternative temperature measuring devices (such as thermocouples or RTDs) is encouraged.

1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 2The test method described as a Method B of this test method, and test methods Ae and Be of ISO 75-1 and ISO 75-2, 1993, are technically equivalent.

PDF Catalog

PDF Pages	PDF Title
1	Scope Referenced Documents Terminology Summary of Test Method
2	Significance and Use Interferences Apparatus FIG. 1
3	Sampling Test Specimen Preparation of Apparatus
4	Conditioning Procedure Report Precision and Bias
5	Keywords TABLE 1 TABLE 2 TABLE 3
6	A1. CALIBRATION OF SINGLE-(CENTRALIZED) TEMPERATURE PROBE UNITS A1.1 A1.2 A1.3
7	A2. CALIBRATION OF MULTI-TEMPERATURE INSTRUMENTS A2.1 A2.2 A2.3 A2.4 A2.5 A2.6 A2.7
8	X1. PROCEDURE FOR DETERMINATION OF CORRECT SPECIMEN LOADING UTILIZING EQUILIBRIUM WEIGHING OF THE LOADING ROD X1.1 Apparatus X1.2 Procedure X2. PROCEDURE FOR DETERMINATION OF CORRECT SPECIMEN LOADING BY WEIGHING THE APPLIED LOAD WITH A TENSION-TESTING MACHINE X2.1 Apparatus FIG. X1.1
9	X2.2 Procedure X3. PROCEDURE FOR DETERMINATION OF CORRECT SPECIMEN LOADING BY WEIGHING THE APPLIED LOAD IN SITU X3.1 Scope X3.2 Apparatus X3.3 Procedure FIG. X2.1
10	X4. PROCEDURE FOR VERIFYING THE CALIBRATION OF PENETRATION MEASURING DEVICES USING GAUGE BLOCKS X4.1 X4.2 FIG. X3.1
11	X4.3 X4.4 X4.5 X4.6 X4.7 X4.8 X5. PROCEDURE FOR DETERMINATION OF SPRING FORCE AND CONDITION OF GAUGE X5.1 Apparatus X5.2 Procedure FIG. X5.1
12	FIG. X5.2 FIG. X5.3

Additional information

Standard Title	D648-07 Standard Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position
Published Code	ASTM
Publication Date	2007
Pages Count	13
ICS Codes	83.080.01 - Plastics in general

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-D648 2007

PDF Catalog

Related products