ASTM-D4703 2007

$44.96

D4703-07 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets

Published By	Publication Date	Number of Pages
ASTM	2007	12

Guaranteed Safe Checkout

Categories: 83.080.20 - Thermoplastic materials, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

ASTM D4703-07

Historical Standard: Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets

ASTM D4703

Scope

1.1 This practice covers the compression molding of thermoplastic granules and milled stock for the preparation of test specimens.

1.2 While conditions for certain materials are given, the primary source of specific conditions shall be the material specification standards for each type of material.

1.3 The values stated in SI units are to be regarded as the standard. The values given in brackets are for information only.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1

The main body of this practice is equivalent to ISO 293-1986. and ISO 293-1986 differ in some details; however, specimens prepared using , Procedure A should be equivalent to those prepared using ISO 293-1986, Cooling Method D. Specimens prepared using , Procedure C should be equivalent to those prepared using ISO 293-1986, Cooling Method B. However, due to the greater cooling rate tolerances of the ISO standard, specimens prepared in accordance with ISO Cooling Method B may not be equivalent to , Procedure C.

Keywords

acrylonitrile-butadiene-styrene (ABS); chlorinated poly(vinyl chloride) (CPVC); compression molding; polyethylene (PE); poly(vinyl chloride) (PVC); styrene-butadiene; test specimen preparation; thermoplastics

ICS Code

ICS Number Code 83.080.20 (Thermoplastic materials)

DOI: 10.1520/D4703-07

PDF Catalog

PDF Pages	PDF Title
1	Scope Referenced Documents Terminology
2	Significance and Use Apparatus FIG. 1 FIG. 2 FIG. 3
3	Procedure TABLE 1
4	Inspection of the Molded Specimens, Plaques, or Sheets Report Precision and Bias Keywords A1. PROCEDURES FOR POLYETHYLENE A1.1 A1.2
5	A1.3 A1.4 A1.5
7	A1.6 A1.7 A1.8
8	A2. SPECIMEN PREPARATION FOR POLYETHYLENE A2.1 A2.2 A3. APPARATUS FOR SPECIMEN PREPARATION OF POLYETHYLENE A3.1 A3.2 A3.3 A3.4 A3.5 TABLE A2.1
9	A3.6 A3.7 A4. MAINTENANCE AND PREPARATION OF EQUIPMENT FOR POLYETHYLENE A4.1 A4.2 A4.3 A4.4 A5. SAMPLING FROM POLYETHYLENE SHEET A5.1 A5.2 A5.3 A6. SPECIMEN PREPARATION AND CONDITIONING A6.1 A6.2 A7. PROCEDURES A7.1 A7.2
10	A7.3 A7.4 A7.5 X1. SUMMARIES OF PROCEDURES FOR CERTAIN THERMOPLASTIC MATERIALS X1.1 Styrene-Butadiene Molding and Extrusion Materials X1.2 Rigid Poly(Vinyl Chloride) Compounds
11	X1.3 Rigid Acrylonitrile-Butadiene-Styrene (ABS) Plastics

Additional information

Standard Title	D4703-07 Standard Practice for Compression Molding Thermoplastic Materials into Test Specimens, Plaques, or Sheets
Published Code	ASTM
Publication Date	2007
Pages Count	12
ICS Codes	83.080.20 - Thermoplastic materials