ASTM-D2990 2001

$44.96

D2990-01 Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics

Published By	Publication Date	Number of Pages
ASTM	2001	20

Guaranteed Safe Checkout

Categories: 83.080.01 - Plastics in general, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

1.1 These test methods cover the determination of tensile and compressive creep and creep-rupture of plastics under specified environmental conditions (see 3.1.3).

1.2 While these test methods outline the use of three-point loading for measurement of creep in flexure, four-point loading (which is used less frequently) can also be used with the equipment and principles as outlined in Test Methods D790.

1.3 For measurements of creep-rupture, tension is the preferred stress mode because for some ductile plastics rupture does not occur in flexure or compression.

1.4 Test data obtained by these test methods are relevant and appropriate for use in engineering design.

1.5 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only.

1.6 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. A specific warning statement is given in 6.8.2.

Note 1This standard and ISO 899 are similar in content, but are not equivalent.

PDF Catalog

PDF Pages	PDF Title
1	Scope Referenced Documents Terminology
2	Summary of Test Methods Significance and Use Apparatus FIG. 1
3	FIG. 2
4	Reagents Test Specimens
5	Conditioning Selection of Test Conditions Procedure
6	Calculation FIG. 3
7	Report Precision and Bias FIG. 4
8	Keywords X1. INTRODUCTION X1.1 FIG. 5 FIG. 6
9	X2. CREEP CURVE X2.1 X2.2 X2.3 X2.4 X2.5 FIG. X2.1
10	X3. CREEP STRENGTH AND CREEP RUPTURE X3.1 X3.2 X3.3 X3.4 X3.5 FIG. X2.2 FIG. X2.3 FIG. X2.4 FIG. X3.1
11	X3.6 X3.7 X4. DATA PRESENTATION X4.1 X4.2 X4.3 FIG. X3.2 FIG. X3.3 FIG. X3.4 FIG. X3.5
12	FIG. X4.1 FIG. X4.2 FIG. X4.3
13	FIG. X4.4 FIG. X4.5
14	X5. PREDICTION OF LONG-TERM PROPERTIES X5.1 FIG. X5.1 FIG. X5.2
15	FIG. X5.3
16	X6. CURVE-FITTING FORMULAS X6.1 X6.2 X6.3 X6.4 X6.5 X6.6 FIG. X6.1
17	X7. HOW TO USE THE CREEP CHART TO DESIGN WITH PLASTICS UNDER STATIC LOAD FIG. X6.2 FIG. X6.3
18	FIG. X7.1
19	X8. SUMMARY X8.1 FIG. X7.1

Additional information

Standard Title	D2990-01 Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics
Published Code	ASTM
Publication Date	2001
Pages Count	20
ICS Codes	83.080.01 - Plastics in general

Preview PDF


PDF Format	Searchable	Printable	Preview Now

ASTM-D2990 2001

PDF Catalog

Related products