ASTM-C887 2005
$44.96
C887-05 Standard Specification for Packaged, Dry, Combined Materials for Surface Bonding Mortar
| Published By | Publication Date | Number of Pages |
| ASTM | 2005 | 11 |
1.1 This specification covers the materials, properties, and packaging of dry, combined materials for use as surface bonding mortar with concrete masonry units that have not been prefaced, coated, or painted.
1.2 This specification does not cover design or application. Consult the manufacturer for specific recommendations.
1.3 of this specification contains the recommended tests for evaluation of surface bonded masonry assemblages used to establish design loads for the composite wall.
1.4 through of this specification contain additional tests that may be performed on surface bonding mortar.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. This hazard statement applies only to Section of this specification.
1.5 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | Scope Referenced Documents Terminology |
| 2 | Materials and Manufacture Proportioning Physical Requirements Sampling and Testing Sampling Surface Bonding Mortar TABLE 1 |
| 3 | Mixing and Testing Surface Bonding Mortar Basis of Rejection Marking and Packaging Keywords |
| 4 | A1. LABORATORY MECHANICAL MIXING OF SURFACE BONDING MORTAR A1.1 Scope A1.2 Apparatus A1.3 Temperature and Humidity A1.4 Procedure for Mixing Surface Bonding Mortar A2. CONSISTENCY TEST OF SURFACE BONDING MORTAR BY CONE PENETROMETER A2.1 Scope A2.2 Apparatus |
| 5 | A2.3 Procedure A2.4 Report A3. FLEXURAL STRENGTH OF SURFACE BONDING MORTAR A3.1 Scope A3.2 Apparatus A3.3 Number of Specimens A3.4 Preparing Specimen Molds A3.5 Procedure A3.6 Calculation |
| 6 | A3.7 Faulty Specimens and Retests A4. COMPRESSIVE STRENGTH OF SURFACE BONDING MORTAR A4.1 Scope A4.2 Apparatus A4.3 Test Specimens A4.4 Procedure A4.5 Calculation A4.6 Faulty Specimens and Retests |
| 7 | A5. TIME OF SET OF SURFACE BONDING MORTAR A5.1 Scope A5.2 Apparatus A5.3 Procedure A6. WATER RETENTION OF SURFACE BONDING MORTAR A6.1 Scope A6.2 Apparatus A6.3 Procedure |
| 8 | A6.4 Calculation X1. RECOMMENDED TESTS FOR EVALUATION OF SURFACE BONDED MASONRY ASSEMBLAGES X1.1 Scope X1.2 |
| 9 | X2. A GUIDE FOR ADDITIONAL TESTS THAT MAY BE PERFORMED ON SURFACE BONDING MORTAR AS REQUIRED BY THE USER X2.1 Scope X2.2 Additional Tests of Surface Bonding Mortar X3. ABSORPTION OF SURFACE BONDING MORTAR X3.1 Scope X3.2 Apparatus X3.3 Procedure X3.4 Calculation X4. RESISTANCE OF SURFACE BONDING MORTAR TO FREEZING AND THAWING X4.1 Scope X4.2 Apparatus X4.3 Procedure X4.4 Calculations X4.5 Report |
| 10 | X5. EARLY STIFFENING OF SURFACE BONDING MORTAR X5.1 Scope X5.2 Apparatus X5.3 Procedure |
| 11 | X5.4 Report X5.5 Interpretation of Results |
