AS 2884.2:2003
$37.70
Heavy mineral sand concentrates – Sampling – Sampling from stationary situations
| Published By | Publication Date | Number of Pages |
| AS | 2003-12-01 | 32 |
Sets out methods for the sampling of heavy mineral sands from stationary situations to provide samples for chemical analysis, physical testing and determination of moisture.
Scope
This Standard sets out methods for the sampling of heavy mineral sands from stationary situations to provide samples for chemical analysis, physical testing and determination of moisture. Stopped-belt sampling is specifically included.
The methods of sampling outlined in this Standard should be considered only where the preferred method of sampling from a moving stream is not possible.
The preparation of samples taken by methods outlined in this Standard is covered in AS 2884.3.
Clauses 4 to 8 provide general sampling theory that may not be relevant to sampling from stationary situations.
Related products
-
AS 2879.2:2003
Alumina – Determination of particles passing a 20 micrometre aperture sieve Published By Publication Date…
-
AS 2888.3:2002 (R2017)
Methods of testing plastics waste fittings – Method for pressure testing of plastics waste fittings…
-
AS 2862.2:2008
Copper, lead, zinc and nickel concentrates – Sampling – Experimental methods for checking the precision…
-
AS/NZS 2381.2:2006
Electrical equipment for explosive atmospheres – Selection, installation and maintenance – Flameproof enclosure ‘d’ Published…
-
AS 2888.2:2002 (R2017)
Methods of testing plastics waste fittings – Method for determining dimensions Published By Publication Date…
-
AS 2187.2:2006
Explosives – Storage and use – Use of explosives Published By Publication Date Number of…
-
AS 2174.2:2006 (R2016)
Heavy road vehicles – Mechanical coupling between prime movers and semitrailers – Interchangeability requirements –…
-
AS 3894.2:2002 (R2013)
Site testing of protective coatings – Non-conductive coatings – Continuity testing – Wet sponge method…
-
AS 2888.7:2002 (R2017)
Methods of testing plastics waste fittings – Method for testing the seal of plastrics waste…
-
AS/NZS 2815.2:2013
Training and certification of occupational divers – Surface supplied diving to 30 m Published By…
-
ISO 28842:2013
Guidelines for simplified design of reinforced concrete bridges Published By Publication Date Number of Pages…
-
IEEE 2888.4-2023
IEEE Standard for Architecture for Virtual Reality Disaster Response Training System with Six Degrees of…
-
AS 2888.8:2002 (R2017)
Methods of testing plastics waste fittings – Thermal cycling test Published By Publication Date Number…
-
AS 2888.4:2002 (R2017)
Methods of testing plastics waste fittings – Method for air pressure/vacuum testing of plastics waste…
-
AS/NZS 3584.2:2008
Diesel engine systems for underground coal mines – Explosion protected Published By Publication Date Number…
-
AS 2582.2:2003 (R2020)
Complete, filled transport packages – Methods of test – Conditioning for testing Published By Publication…
-
AS/NZS 4864.2:2008
Performance of refrigerated beverage vending machines – Minimum energy performance standard (MEPS) requirements Published By…
-
IEEE 2888.4-2023
IEEE Standard for Architecture for Virtual Reality Disaster Response Training System with Six Degrees of…
-
AS 2864.1:2003
Methods for the analysis of rutile – Determination of titanium content – Titrimetric method Published…
-
AS 2832.2:2003 (R2016)
Cathodic protection of metals – Compact buried structures Published By Publication Date Number of Pages…
-
IEEE 2888.1-2023
IEEE Standard for Specification of Sensor Interface for Cyber and Physical Worlds (Published) Published By…
-
AS 2898.2:2003
Radar speed detection – Operational procedures Published By Publication Date Number of Pages AS 2003-08-11…
-
IEEE 2888.2-2023
IEEE Standard for Actuator Interface for Cyber and Physical Worlds (Published) Published By Publication Date…
-
AS 2888.9:2002 (R2017)
Methods of testing plastics waste fittings – Method for determining residual stress in plastics waste…
-
AS 2888.6:2002 (R2017)
Methods of testing plastics waste fittings – Method for load testing of plastics waste outlets…
-
IEEE 2888.2-2023
IEEE Standard for Actuator Interface for Cyber and Physical Worlds (Published) Published By Publication Date…
-
IEEE 2888.2-2023
IEEE Standard for Actuator Interface for Cyber and Physical Worlds (Published) Published By Publication Date…
-
AS 2434.2:2002 (R2013)
Methods for the analysis and testing of lower rank coal and its chars – Lower…
-
IEEE 2888.4-2023
IEEE Standard for Architecture for Virtual Reality Disaster Response Training System with Six Degrees of…
-
AS 2944.2:2007
Plastics pipes and fittings for gas reticulation – Polyamide fittings Published By Publication Date Number…
-
IEEE 2888.1-2023
IEEE Standard for Specification of Sensor Interface for Cyber and Physical Worlds (Published) Published By…
-
AS 2888.0:2002 (R2017)
Methods of testing plastics waste fittings – Introduction and list of methods Published By Publication…
-
AS 2986.2:2003 (R2016)
Workplace air quality – Sampling and anlysis of volatile organic compounds by solvent desorption/gas chromatography…
-
ATS 4888.2:2013
Electronic transfer of prescriptions – Platform independent (logical) services model to support electronic transfer of…
-
AS 2884.3:2003
Heavy mineral sand concentrates – Sampling – Preparation of samples Published By Publication Date Number…
-
AS 2888.5:2002 (R2017)
Methods of testing plastics waste fittings – Trap seal test Published By Publication Date Number…
-
AS 2888.1:2002 (R2017)
Methods of testing plastics waste fittings – Method of determining the suitability of connection threads…
-
ISO 28841:2013
Guidelines for simplified seismic assessment and rehabilitation of concrete buildings Published By Publication Date Number…
-
IEEE 2888.1-2023
IEEE Standard for Specification of Sensor Interface for Cyber and Physical Worlds (Published) Published By…
-
AS 2224.2:2009
Medicine measures – Plastic Published By Publication Date Number of Pages AS 2009-05-13 28
