AS 2518:1992
$27.30
Fusion-bonded low-density polyethylene coating for pipes and fittings
| Published By | Publication Date | Number of Pages |
| AS | 1992-07-20 | 17 |
Specifies requirements for coating for protection against corrosion, where the coating is not subject to weather exposure (a safe period of 18 months of weather exposure is allowed for to cover an extended storage period prior to installation), and the pipeline operating temperatures are not above 60°C nor below -40°C. Coating thickness for normal and heavy duty for a given range of nominal pipe sizes are tabulated.
Scope
This Standard specifies requirements for fusion-bonded low-density polyethylene coating of pipes and fittings for protection against corrosion. The coating is intended for use on pipes and fittings that are installed in locations not subject to weather exposure, although a safe period of 18 months of weather exposure is allowed for to cover the storage period prior to installation.
NOTES:
1 Advisory information on methods of determining compliance of a 'lot' with this Standard is given in Appendix A.
2 Guidelines to purchasers on requirements that are to be specified by the purchaser and those that are to be or may be agreed upon at the time of enquiry or order are given in Appendix B.
3 The attention of purchasers is drawn to the necessity to ascertain the expected weathering period of the coating before installation, and in the likelihood of 18 months being exceeded, to make provision for shielding of the coating from direct sunlight.
Polyethylene materials complying with this Standard are intended for application to pipes and fittings where the pipeline operating temperatures are not normally more than 60°C nor less than -40°C.
Related products
-
AS 2519:1993 (R2013)
Guide to the technical evaluation of higher rank coal deposits Published By Publication Date Number…
-
JIS K 2518:1991
Petroleum Products – Lubricating Oils – Determination of Foaming Characteristics Published By Publication Date Number…
-
ISO 19942:2018
Maïs (Zea mays L.) — Spécifications Published By Publication Date Number of Pages ISO 2018-07…
-
BS EN 25183-2:1992
Resistance spot welding. Electrode adaptors, male taper 1:10 – Parallel shank fixing for end-thrust electrodes…
-
SAE MA 2538:1992
Gasket, Metal C-Ring Seal Nickel Alloy, Corrosion and Heat Resistant, Metric Procurement Specification for Published…
-
ISO 1518:1992
Paints and varnishes — Scratch test Published By Publication Date Number of Pages ISO 1992-03…
-
NFPA 1982 2018
NFPA 1982: Standard on Personal Alert Safety Systems (PASS) Published By Publication Date Number of…
-
AS 2818:1993
Guide to swimming pool safety Published By Publication Date Number of Pages AS 1993-07-26 15
-
JIS C 2516:1990
Pot-cores made of ferromagnetic oxide Published By Publication Date Number of Pages JIS 1990-10-01 40
-
ISO 1997:2018
Granulated cork and cork powder — Classification, properties and packing Published By Publication Date Number…
-
NFPA 1999 2018
NFPA 1999: Standard on Protective Clothing and Ensembles for Emergency Medical Operations Published By Publication…
-
BS EN 1992-4:2018
Eurocode 2. Design of concrete structures – Design of fastenings for use in concrete Published…
-
JIS C 2528:1991
Silk and polyester fiber covered wires for electrical resistance use Published By Publication Date Number…
-
BS 2588-1:1992
Portable sanitary pans for use in healthcare establishments. – Specification for reusable bed pans Published…
-
BS 2588-2:1992
Portable sanitary pans for use in healthcare establishments – Specification for reusable pans for commode…
-
IPC FA-251:1992
Assembly Guidelines for Single-Sided and Double- Sided Flexible Printed Circuits Published By Publication Date Number…
-
JIS A 6518:1994
Components for Wire Net Fences Published By Publication Date Number of Pages JIS 1994-02-01 18
-
BS 7518:1995
Radiation protection instrumentation. Portable, transportable or installed equipment to measure x or gamma radiation for…
-
JIS B 1518:1992
Dynamic load ratings and rating life for rolling bearings Published By Publication Date Number of…
-
NFPA 1999 2018
NFPA 1999: Standard on Protective Clothing and Ensembles for Emergency Medical Operations Published By Publication…
-
IEEE 518 1982
IEEE Guide for the Installation of Electrical Equipment to Minimize Electrical Noise Inputs to Controllers…
-
ISO 2598-2:1992
Iron ores — Determination of silicon content — Part 2: Reduced molybdosilicate spectrophotometric method Published…
-
NFPA 1994 2018
NFPA 1994: Standard on Protective Ensembles for First Responders to CBRN Terrorism Incidents Published By…
-
ISO 19927:2018
Fibre-reinforced plastic composites — Determination of interlaminar strength and modulus by double beam shear test…
-
ISO 2538:1998
Geometrical Product Specifications (GPS) — Series of angles and slopes on prisms Published By Publication…
-
ISO 2818:1994
Plastics — Preparation of test specimens by machining Published By Publication Date Number of Pages…
-
ISO 2598-1:1992
Iron ores — Determination of silicon content — Part 1: Gravimetric methods Published By Publication…
-
NFPA 1192 2018
NFPA 1192: Standard on Recreational Vehicles Published By Publication Date Number of Pages NFPA 2018…
-
JIS R 2618:1992
Testing Method for Thermal Conductivity of Insulating Fire Bricks by Hot Wire Published By Publication…
-
UL 1998:2018
Standard for Software in Programmable Components Published By Publication Date Number of Pages UL 2018-09-24…
-
ISO 16992:2018
Pneumatiques pour voitures particulières — Équipements de substitution de roue de secours (SUSE) Published By…
-
BS EN 25183-1:1992
Resistance spot welding. Electrode adaptors, male taper 1:10 – Conical fixing, taper 1:10 Published By…
-
AS/NZS 2538:1995
Vehicle support stands Published By Publication Date Number of Pages AS 1995-06-05 17
-
ISO 2528:1995
Sheet materials — Determination of water vapour transmission rate — Gravimetric (dish) method Published By…
-
ISO 2578:1993
Plastics — Determination of time-temperature limits after prolonged exposure to heat Published By Publication Date…
-
NFPA 1962 2018
NFPA 1962: Standard for the Care, Use, Inspection, Service Testing, and Replacement of Fire Hose,…
-
ISO 1922:2018
Rigid cellular plastics — Determination of shear properties Published By Publication Date Number of Pages…
-
BS EN 2318:1992
Aluminium alloy AL-P2024-T3511. Extruded bars and sections 1,2 mm ≤ a or D ≤ 150…
-
UL 1995:2018
Heating and Cooling Equipment Published By Publication Date Number of Pages UL 2018-08-17 195
-
AS 2418:1995 (R2013)
Coal and coke – Glossary of terms Published By Publication Date Number of Pages AS…
